Latest effective CWNP CWNA-106 exam dumps-100% Free | Softwarexam

Get really useful CWNP CWNA-106 exam content at Pass4itsure,softwarexam free CWNP CWNA-106 exam dump and CWNA-106 PDF (30q&as)
Free Download from Pass4itsure
Latest CWNP CWNA-106 Exam dumps at pass4itsure.com!
100% pass guarantee! To get the CWNP CWNA-106 Exam certification does not need to be so hard,
choose Pass4itsure CWNA-106 PDF or CWNA-106 VCE guarantee once pass the exam.
All of our exam databases are updated throughout the year. The following questions and answers are issued by
the official CWNP Test Center: https://www.pass4itsure.com/cwna-106.html

[PDF] Free CWNP CWNA-106 dumps download from Google Drive: https://drive.google.com/open?id=1zcKs8bnUrFt4ZJa6fmneUn1BPQXUEN-f

[PDF] Free Cisco 500-325 dumps download from Google Drive: https://drive.google.com/open?id=1p4nIB3LhUuJqqjuxkFCZERrI66ZQ3Oqf

CWNA (Wi-Fi Administration), Certified Wireless Network Administrator -CWNA: https://www.cwnp.com/certifications/cwna

Pass4itsure offers the latest CWNA-106 practice test free of charge (30Q&As)

QUESTION 1
ABC Company has just purchased a 6 dBi patch antenna. After performing some tests with the 6 dBi antenna, they
have concluded that more antenna gain is needed to cover their outdoor courtyard.
When choosing an antenna with higher gain, what other antenna characteristic will also always change?
A. Fresnel Zone size
B. Maximum input power
C. Beamwidth
D. Impedance
E. VSWR Ratio
Correct Answer: C

QUESTION 2
ABC Company is planning a point-to-multipoint outdoor bridge deployment with standalone (autonomous) 802.11 bridge
units. 802.1X/EAP will be used for bridge authentication. A Linux- based RADIUS server will be used for authentication.
What device in the bridge implementation acts as the 802.1X Authenticator?
A. The RADIUS server
B. All non-root bridges
C. A designated non-root bridge
D. The root bridge
E. The Ethernet switch
Correct Answer: D

QUESTION 3
What is an advantage of using WPA2-Personal instead of WEP-128 as a security solution for 802.11 networks?
A. WPA2-Personal uses 802.1X/EAP for authentication, and WEP-128 uses preshared keys.
B. WPA2-Personal is based on IEEE 802.11 industry standards, but WEP is not.
C. WPA2-Personal uses CCMP for encryption, and WEP-128 uses TKIP for encryption.
D. WPA2-Personal uses dynamic encryption keys, and WEP-128 uses static keys.
E. WPA2-Personal requires complex 64-character hex keys, whereas WEP-128 requires weak 26- character hex keys.
Correct Answer: D

QUESTION 4
Your consulting firm has recently been hired to complete a site survey for a company. Your engineers use predictive
modeling software for surveying, but the company insists on a pre- deployment site visit. What tasks should be
performed as part of the pre-deployment visit to prepare for a predictive survey? (Choose 2)
A. With a spectrum analyzer, identify the type, amplitude, and location of RF interference sources, if any are present.
B. Evaluate the building materials at ABC\’s facility and confirm that the floor plan documents are consistent with the
actual building.
C. Test several antenna types connected to the intended APs for use in the eventual deployment.
D. Collect information about the company\’s security requirements and the current configuration of their RADIUS and
user database servers.
E. Install at least one AP on each side of the exterior walls to test for co-channel interference through these walls.
Correct Answer: AB

QUESTION 5
As defined in the 802.11 specification, legacy Power Save requires an inefficient back-and-forth frame exchange
process. Due to this inefficiency, many WLAN device implementations use a variation of 802.11 Power Save to
accomplish the same function.
What non-standard power save behavior is used by most Wi-Fi devices in actual legacy Power Save implementations?
A. Client devices ignore the TIM field and automatically send PS-Poll frames after every beacon.
B. After each beacon, the AP attempts to empty its frame buffer by sending Wake- on-WLAN frames to wake each
dozing client.
C. Request-to-Send and Clear-to-Send frame exchanges are used to trigger the delivery of buffered data.
D. The Beacon interval is changed from the default 100 time units to 10 or less time units.
E. Clients send null data frames to the AP and switch the power management bit from 1 to 0 to receive queued data.
F. Stations send a CTS-to-self frame to the AP with a very long duration period so they can receive all of their buffered
data at once.
Correct Answer: E

QUESTION 6
ABC Company has a 2.4 and 5 GHz WLAN deployment. DFS functionality is enabled as required by the regulatory
domain and APs use DFS channels as long as radar is not detected. Band steering is also enabled to encourage dual-
band clients to use frequency bands with more capacity. Your performance analysis shows that many dual-band VoWiFi
client devices will move back and forth between 2.4 and 5 GHz as the users roam throughout the building. All APs have
2.4 and 5 GHz radios enabled with transmit power adjusted to accommodate relatively similar cell sizes. This
andquot;band hoppingandquot; behavior is viewed by network staff to be undesirable.
What is the most likely cause of the unpredictable client band selection behavior?
A. Interference from 5 GHz radar sources has increased frame corruption and retries on channels 36-48.
B. 5 GHz frequencies offer better RF penetration than 2.4 GHz, but 2.4 GHz offers more voice call capacity and lower
latency than 5 GHz. C. The voice client does not support DFS, and therefore experiences some 5 GHz coverage holes as it moves through
the network.
D. The client\’s band selection algorithm prefers 5 GHz, but band steering behavior usually steers 75-85% of client
devices to 2.4 GHz.
Correct Answer: C

QUESTION 7
What can cause an excessively high VSWR (Voltage Standing Wave Ratio) in a WLAN RF transmission line?
A. An impedance mismatch in the RF cables and connectors
B. Reflected direct current (DC) voltage on the main RF signal line
C. Attenuation of the RF signal as it travels along the main signal path
D. Crosstalk (inductance) between adjacent RF conductors
Correct Answer: A

QUESTION 8
What statement describes the authorization component of a AAA implementation?
A. Verifying that a user is who he says he is
B. Validating client device credentials against a database
C. Logging the details of user network behavior in order to review it at a later time
D. Granting access to specific network services according to a user profile
E. Implementing a WIPS as a full-time monitoring solution to enforce policies
Correct Answer: D

QUESTION 9
To ease user complexity, your company has implemented a single SSID for all employees. However, the network
administrator needs a way to control the network resources that can be accessed by each employee based on their
department.
What WLAN feature would allow the network administrator to accomplish this task?
A. SNMP
B. VRRP
C. RBAC
D. IPSec
E. WIPS
F. WPA2
Correct Answer: C

QUESTION 10
What is the intended use for the WLAN hardware known as a pole or mast mount unit?
A. Mounting a lightning arrestor to a grounding rod
B. Mounting an omnidirectional antenna to a mast
C. Mounting an RF amplifier to a dipole antenna
D. Mounting a PoE injector to a perforated radome
E. Mounting an access point to a site survey tripod
Correct Answer: B

QUESTION 11
How is throughput capacity scaled in a single channel architecture (SCA) WLAN system?
A. By increasing transmit power and placing APs that are on a single channel farther from one another.
B. By adding more SSIDs to existing APs to spread users across different contention domains.
C. By adding non-overlapping channel layers through the addition of more APs.
D. By using downlink data compression and uplink flow control at the AP.
E. By using a single 802.11n radio to transmit simultaneous downlink data streams to different users.
Correct Answer: C

QUESTION 12
A Wi-Fi Alliance interoperability certificate indicates that a device is a/b/g/n certified. It further indicates one transmit and
receive spatial stream for both the 2.4 GHz and 5.0 GHz bands. It further indicates support for both WPA and WPA2
Enterprise and Personal. Finally, it indicates support for EAP-TLS, EAP-TTLS/ MSCHAPv2, PEAPv0/EAP-MSCHAPv2
and PEAPv1/EAP- GTC.
Which one of the following statements is false?
A. This client device supports protection mechanisms such as RTS/CTS and/or CTS- to-Self.
B. This client device supports both TKIP and CCMP cipher suites.
C. 300 Mbps is the maximum supported data rate for this device.
D. This client device supports the ERP, OFDM, and HT physical layer specifications.
E. This client device supports X.509 certificates for EAP authentication.
Correct Answer: C

QUESTION 13
What HT technology requires MIMO support on both the transmitter and receiver?
A. Spatial multiplexing
B. Short guard intervals
C. Maximal ratio combining
D. Orthogonal Frequency Division Multiplexing
Correct Answer: A

QUESTION 14
What terms accurately complete the following sentence? The IEEE 802.11-2012 standard specifies mandatory support
of the ___________ cipher suite for Robust Security Network Associations, and optional use of the ___________ cipher
suite, which is designed for use with pre-RSNA hardware.
A. CCMP, TKIP
B. 802.1X/EAP, WEP
C. TLS, SSL
D. CCKM, WEP
E. RC5, RC4
Correct Answer: A

QUESTION 15
You were previously onsite at XYZ\’s facility to conduct a pre-deployment RF site survey. The WLAN has been deployed
according to your recommendations and you are onsite again to perform a post- deployment validation survey.
When performing this type of post-deployment RF site survey for VoWiFi, what are two steps that must be performed?
(Choose 2)
A. Coverage analysis to verify appropriate coverage and roaming boundaries
B. Spectrum analysis to locate and identify RF interference sources
C. Frequency-band hopping analysis to detect improper RF channel implementations
D. Protocol analysis to discover channel use on neighboring APs
E. Application analysis with an active phone call on a VoWiFi handset
Correct Answer: AE

QUESTION 16
What are two channel modes specified by the 802.11n (High Throughput) PHY? (Choose 2)
A. 20 MHz
B. 20/40 MHz C. 40/80 MHz
D. 22 MHz
E. 80 MHz
F. 160 MHz
Correct Answer: AB

QUESTION 17
What term describes the effect of increasing the intensity of an RF wave with an antenna by focusing the energy in a
specific direction?
A. Distributed Radiation
B. Active Amplification
C. Beam Compression
D. Passive Gain
E. RF Flooding
Correct Answer: D

QUESTION 18
As you prepare for a site survey in a multi-floor corporate office, you have learned about several wireless devices that
support connection-oriented, real-time applications. These applications are sensitive to service interruptions and require
excellent signal quality, low latency, and low loss. For that reason, it is important to identify sources of RF interference
as well as building characteristics that would cause RF blockage or dead spots.
What systems or environmental characteristics are most likely to cause interference or RF blockage and disrupt service
for these applications? (Choose 2)
A. Microwave ovens
B. Narrow hallways
C. Elevator shafts
D. RFID chokepoints
E. Workspace dividers
Correct Answer: AC

QUESTION 19
During the discovery and connectivity process, client and AP stations exchange information about their supported data
rates. After the association, how do client and AP stations select the supported data rate that will be used to send an
802.11 data frame?
A. During the association, the client and AP agree to use the same transmit rate, but either station can request a change
at any time after the association. B. The client and AP each choose the optimal data rate to use independently of one another, based on their own
measurements related to the RF link.
C. The client and AP may use different transmit rates, but the AP determines the data rate that will be used by each
client station in the BSS.
D. The client and AP may use different transmit rates, but the client determines the data rate that it will use and the data
rate that the AP will use when communicating to the client.
E. The client and AP may use a different transmit rates, but the transmit rate is determined by the peer station, based on
the peer\’s experience of the RF link.
Correct Answer: B

QUESTION 20
What facts are true regarding controllers and APs in a Split MAC architecture? (Choose 2)
A. An IP tunnel is established between the AP and controller for AP management and control functions.
B. Using centralized data forwarding, APs never tag Ethernet frames with VLAN identifiers or 802.1p CoS.
C. With 802.1X/EAP security, the AP acts as the supplicant and the controller acts as the authenticator.
D. Management and data frame types must be processed locally by the AP, while control frame types must be sent to
the controller.
E. In a distributed data forwarding model, the AP handles frame encryption and decryption.
Correct Answer: AE

QUESTION 21
What statements about the beamwidth of an RF antenna are true? (Choose 2)
A. The lower the gain of an antenna, the more narrow one or both beamwidths become.
B. The beamwidth patterns on an antenna polar chart indicate the point at which the RF signal stops propagating.
C. Horizontal and vertical beamwidth are calculated at the points in which the main lobe decreases power by 3 dB.
D. Horizontal beamwidth is displayed (in degrees) on the antenna\’s Azimuth Chart.
Correct Answer: CD

QUESTION 22
In addition to coverage analysis results, what should be included in a site survey report to ensure WLAN users
experience acceptable performance?
A. Application Layer protocol availability analysis results
B. Layer 4 protocol availability analysis results
C. Capacity analysis results
D. WAN interface analysis results
Correct Answer: C

QUESTION 23
You are the network administrator for ABC Company. Your manager has recently attended a wireless security seminar.
The seminar speaker taught that a wireless network could be hidden from potential intruders if you disabled the
broadcasting of the SSID in Beacons and configured the access points not to respond to Probe Request frames that
have a null SSID field. Your manager suggests implementing these security practices.
What response should you give to this suggestion? (Choose 2)
A. Any 802.11 protocol analyzer can see the SSID in clear text in frames other than Beacons and Probe Response
frames. This negates any security benefit of trying to hide the SSID in Beacons and Probe Response frames.
B. This security practice prevents manufacturers\’ client utilities from detecting the SSID. As a result, the SSID cannot
be obtained by attackers, except through social engineering, guessing, or use of a WIPS.
C. Although it does not benefit the security posture, hiding the SSID in Beacons and Probe Response frames can be
helpful for preventing some users (such as guests) from attempting to connect to the corporate network.
D. Any tenants in the same building using advanced penetration testing tools will be able to obtain the SSID by
exploiting WPA EAPOL-Key exchanges. This poses an additional risk of exposing the WPA key.
E. To improve security by hiding the SSID, the AP and client stations must both be configured to remove the SSID from
association request and response frames. Most WLAN products support this.
Correct Answer: AC

QUESTION 24
In a Wi-Fi client configuration utility, what feature is most likely to be user configurable?
A. 802.1p to WMM mappings
B. SNMPv3 Users
C. WMM-PS Dozing Interval
D. RADIUS Server IP Address
E. EAP Authentication Type
Correct Answer: E

QUESTION 25
Which IEEE 802.11 physical layer (PHY) specifications include support for and compatibility of both OFDM and
HR/DSSS? (Choose 2)
A. HR/DSSS (802.11b)
B. OFDM (802.11a)
C. ERP (802.11g)
D. HT (802.11n) E. CCK (802.11b)
F. VHT (802.11ac)
Correct Answer: CD

QUESTION 26
What causes of hidden nodes within a BSS would be more likely lead to an increase in collisions and retries? (Choose
2)
A. Data frames too large for the physical environment
B. Client stations broadcasting with too much power
C. Access points broadcasting with too little power
D. Client stations too close in proximity to each other
E. Obstacles between client stations causing attenuation
F. Large 802.11 cells with physically distributed stations
Correct Answer: EF

QUESTION 27
What phrase defines Equivalent Isotropically Radiated Power (EIRP)?
A. The power output from the radio into the RF cable
B. The power output from the radio after cable losses
C. The highest RF signal strength that is transmitted from a given antenna
D. Reflected power due to an impedance mismatch in the signal path
E. Power supplied from the transmission line to the antenna input
Correct Answer: C

QUESTION 28
When using an RF splitter to connect one transceiver to sector antennas loss is incurred.
What is this loss called?
A. Conversion loss
B. Through loss
C. Active loss
D. Intentional loss
Correct Answer: B

QUESTION 29
In an enterprise WLAN, what condition will prevent a dual-band VHT/HT client device from performing a fast and
seamless transition (i.e. latency-sensitive applications are not disrupted) between two access points that are managed
by the same WLAN controller?
A. The current AP is using channel 1 and the new AP is using channel 40.
B. The SSID of the current AP does not match the SSID of the new AP.
C. The current AP supports only HT and the new AP is VHT capable.
D. The access points are hiding the SSID in Beacons and Probe Response frames.
Correct Answer: B

QUESTION 30
When performing a site survey for a Multiple Channel Architecture (MCA) system in a multi- tenant building with five
floors, what aspect should you, as the site surveyor, keep in mind?
A. The RF interference caused by passing airplanes supporting on-board Wi-Fi should be a prime consideration.
B. The omni-directional antennas of the access points should be oriented parallel to the floor to maximize the coverage
pattern across as many floors as possible.
C. The channel reuse pattern should be three dimensional with the RF cell extending coverage of each access point to
other floors.
D. The Fresnel Zone is completely blocked between floors so each floor is considered a separate site survey.
Correct Answer: C

Get really useful CWNP CWNA-106 exam content at Pass4itsure,softwarexam free CWNP CWNA-106 exam dump and CWNA-106 PDF (30q&as)
Free Download from Pass4itsure.If you want to prepare for CWNA-106 exam in shortest time, with minimum effort but for most effective result,
you can use Pass4itsure CWNA-106 dumps which simulates the actual testing environment and allows you to focus on various
sections of CWNA-106 exam. Best of luck!

[PDF] Free CWNP CWNA-106 dumps download from Google Drive:
https://drive.google.com/open?id=1zcKs8bnUrFt4ZJa6fmneUn1BPQXUEN-f

[PDF] Free Cisco 500-325 dumps download from Google Drive:
https://drive.google.com/open?id=1p4nIB3LhUuJqqjuxkFCZERrI66ZQ3Oqf

Pass4itsure Coupon Code 15% Off

pass4itsure coupon

related: https://www.softwarexam.com/most-important-cisco-300-101-dumps-practice-exam.html