Free Valuable Latest Download HP0-J26 Certification Guarantee You 100% Pass Download

QUESTION 1
To install additional switches, you must determine the ideal ISL ratio. Which ISL ratio range is recommended for less I/O intensive application requirements (less than 70 MB/s at 2 Gb/s, less than 140 MB/s at 4 Gb/s, less than 280 MB/s at 8 Gb/s)?
A. 3:1 to 1:1
B. 1:1 to 3:1
C. 15:1 to 7:1
D. 7:1 to 15:1

Correct Answer: D
QUESTION 2
Which Fibre Channel timing variables must match in an interoperable fabric?
A. Timing variables do not need to match.
B. R_A_TOV, E_D_TOV and B_B_TOV
C. R_A_TOV and E_D_TOV
D. R_A_TOV and B_B_TOV

Correct Answer: C
QUESTION 3
You are preparing an installation plan for implementing a new SAN design and want to ensure all customer needs are included. Which data collection method requires that you create a process list and review all relevant stakeholders?
A. Card Arrangement
B. Information Extraction
C. Brainstorming
D. Process Mapping

Correct Answer: B
QUESTION 4
Which information should be included in the topology map documentation of a SAN design provided to your support organization? (Select two.)
A. serial numbers of connected servers
B. SAN switch zoning configurations
C. storage controller operating mode parameters
D. IP addresses of the connected servers
E. World Wide Names of all nodes and devices

Correct Answer: BE
QUESTION 5
You are implementing a SAN infrastructure including an HP StorageWorks EVA4400 at Your customer site. The customer is interested in using three-site cascaded replication functionality. What should you recommend to accomplish this? (Select two).
A. HPStorageWorks FlexCopy
B. HP Continuous Access EVA
C. additional disks in the EVA
D. HP Virtual Replicator
E. HP Business Copy EVA

Correct Answer: BE
QUESTION 6
Which HP tool provides the ability to create a Microsoft Visio diagram of a SAN topology for Your customer documentation?
A. SAN Health
B. SAN Designer
C. SAN Visibility
D. SAN Navigator

Correct Answer: C
QUESTION 7
A single Fibre Channel router is implemented in an existing SAN. What can be accomplished?
A. fabric management service
B. fabric interconnection without merge
C. SAN availability improvement
D. SAN extension across long distances

Correct Answer: B
QUESTION 8
Which features can affect performance in a SAN? (Select three.)
A. cable modes
B. number of ISLs
C. type of LC connector
D. storage array configuration
E. type and capacity of disks used
F. storage access restrictions

Correct Answer: BDE
QUESTION 9
What has the most influence on the response time of a hard disk drive?
A. arbitration
B. host request
C. rotational delay
D. seek time

Correct Answer: C
QUESTION 10
You are preparing for a homogeneous fabric merge and notice the customer set the same domain ID for all fabrics. What will happen if this is not corrected?
A. Enabled zone configurations are immediately disabled.
B. Domain IDs remain unchanged and the fabrics become segmented.
C. Domain IDs are automatically renumbered and the fabrics merge, but port zoning is affected.
D. Domain IDs are automatically renumbered and the fabrics merge without any side effect.
Correct Answer: B QUESTION 11
Which method should you use to quickly and easily document a new customer SAN configuration?
A. Follow all cabling from port to port, write down source and target of the cables, label the cables, and record the labels.
B. Collect the customer’s configuration data using SANVisibility, upload the data and verify the report as soon as you get the documents.
C. Install HP SIM and HP Storage Essentials SRM in 60-day trial mode on a new Windows Central Management Server and collect the site information to evaluate the result with Report Designer
D. UseFinisar Fibre Channel Sniffer to determine source, destination, quality and performance of the Fibre Channel configuration.

Correct Answer: B